Peugeot Keys Tips From The Top In The Business
Peugeot 208 Key Replacement
It is better to leave the replacement of Peugeot 208 keys to auto locksmiths with the right equipment and skills. They will be able to make and program new keys much quicker than a dealership and at a lower cost.
A dead coin battery is the most likely cause the reason your key-fob stops locking or unlocking the doors. However, there are many other reasons why the key might be malfunctioning.
Dead Coin Battery
A dead coin battery can stop your Peugeot 208 from locking or unlocking, and will not start the engine. In this instance you'll have to use the alternative starting method that is described in the owner's manual.
The spark plugs can also be worn out. The spark plugs light the fuel to start the engine. They have a limited life span. If they're not used enough to last, they'll eventually fail.
There is an easy solution to this issue. Examine the voltage of your battery with a multimeter. If the voltage falls below 11,5 volts, it's the time to replace it. If the battery is corroded, it is important to clean its contacts. This can be done by removing the rubber cover from the two battery terminals and then using a wirebrush to remove any damaged parts of the battery. Then, you must reconnect the positive and negative pole cables.
Water Damage
If your 208 won't start and the battery isn't flat then you should check that the spark plugs are working. It could be that they're dirty, causing them not to spark. The spark plugs can be cleaned in an workshop.
Peugeot cars have transponder keys that is compatible with the car's immobiliser system. This guarantees that only the right key is able to start the engine. If the chip inside the Peugeot key is damaged, then it won't send the proper signal to the vehicle.
Water damage is a common cause of this problem. This is a common problem in colder climates where the vehicle is exposed to snow or rain. If this is the case, you should contact a reputable auto locksmith who has all the tools and equipment needed to modify the new key. They also have the most up-to-date technology and equipment needed to make a Peugeot 208 smart key. The process shouldn't take longer than 15 minutes.
Faulty battery contacts
Peugeot replaced the old transponder chips with a new version that makes use of electronic components that are mounted on a circuit board. This new technology works great when it's brand new however, over time, the circuit boards start to lose their effectiveness and cease working correctly.
This could prevent the immobiliser chip from working which means that your car won't start. If this is the case, it's a good idea to seek out a Peugeot specialist or locksmith.
A common issue is when the battery of the key fob starts to die. This causes the blade of the key to stop feeding into the lock. A locksmith from your car will replace the battery, and then cut a fresh blade for you. This is a quick solution.
peugeot 107 key programming could be that the receiver module is malfunctioning when your Peugeot key fob stops working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver module is responsible for transmitting radio signals to the onboard computer which regulates the central locking system of your Peugeot vehicle.
The key fob itself is fitted with rubber seals to prevent water from getting to the chip inside. However, prolonged exposure to water may be able to penetrate these seals and cause damage to the chip. The high salt content of the pool or ocean water can cause damage to the key fob, especially if it is submerged.
The module will need to be replaced if your Peugeot spare key isn't working anymore. This can only by done by an Peugeot specialist or an expert auto locksmith. Peugeot keys, unlike other cars, are secured by an immobilizer device. This requires the correct codes to start the car. This is why you must be able to trust a professional Peugeot locksmith to take on the job of creating and programming an appropriate replacement.
Computer malfunctioning on-board
The computer on board in your Peugeot is responsible for many of the systems inside your car, ranging from power windows to airbags. If something goes wrong with these systems, it will usually show a code that identifies the issue. This code is saved in the system and will remain there until the issue is resolved. This may require the on-board computers to be replaced.
One of the most frequent causes of the airbag light coming on is loose or corroded connections in the airbag sensor. This could be due to wear and tear, aging or exposure to salt and moisture. It is imperative to have this issue addressed as quickly as you can, as the airbag malfunctioning could be dangerous in the event of an accident.
If your Peugeot is showing a card not detected error then the key battery inside the key fob could be weak or dead. This can prevent the key fob from sending a signal that disarms the standard immobilizer in your vehicle. Test this by pressing the unlock key on the fob's key, then trying to start your vehicle. If this does not work the battery on the key is in need of replacement.